Shure Logo.png

How to Read a Microphone Frequency Response Chart

Shopping for a new microphone? Then, you'll want to understand its frequency response. This article will explain the basics: how it's measured, how to interpret a frequency response chart, and how to match the frequency response of the mic to the sound source.
February, 05 2015 |

While headphone and earbud packaging that boasts a frequency range outside your ability to hear sound is just, well, a marketing tactic, the same is not true of microphone frequency response charts. You can't buy a microphone without running into a frequency response chart. Here's why: A frequency response chart tells you a lot about which mic is appropriate for any given application and which mic is not. What if you don't know what the chart means, though? Charts and graphs are intended to simplify an explanation, but sometimes, they can just cause more confusion.


Creating the Chart

A frequency response chart is generated by testing the microphone in an anechoic chamber. An anechoic chamber is a specially constructed room just for audio testing: a controlled atmosphere where the room is acoustically dead, without any form of sound reflection.

The Shure Anechoic Chamber
The Shure Anechoic Chamber

A mic is set up in front of the calibrated loudspeaker. Pink noise is played. (If you're not familiar with the term, pink noise is all frequencies with equal energy in every octave.) The microphone signal is routed into a spectrum analyzer and a frequency response chart is produced.


Reading the Chart

The chart is usually over the 20 Hz to 20 kHz range, which is the range of human hearing. So, how do you read it?

The horizontal numbers in a microphone frequency response chart indicate frequencies (again, usually over the 20 Hz to 20 kHz range), and the vertical numbers represent relative output level in dB (decibels). As you look at a frequency chart, you can tell how a given microphone performs at certain frequencies.


Comparing Two Popular Shure Mics

How is this information helpful?  Let's look at a couple of examples.

Here's the ubiquitous Shure SM57's frequency chart:

SM57 Frequency Response Chart
SM57 Frequency Response Chart

The frequency response of the SM57 makes it especially good for certain instruments such as a snare drum because the fundamental frequency of the snare resides in the 150 Hz to 250 Hz range, right where the SM57 frequency chart shows that the SM57 response is flat or neutral.

In other words, at this frequency, what you hear going into the microphone is what you will tend to hear coming out: nothing more, nothing less.

The presence bump on the right of the chart is just where the frequency of the "snap" of the snare resides. In addition, its rolled off low-end makes it great for downplaying the kick drum, which is often very close to the snare. This combination is what most engineers are looking for in a great snare drum mic: the ability to capture the true sound of the snare, accentuate its snap, and reject other instruments in close proximity.

Now, let's look at another popular Shure mic: the BETA 58A®.

Beta58A Frequency Response Chart
Beta58A Frequency Response Chart

The BETA 58A is a popular model for vocals. The rising frequency response from 2,000 to 10,000 Hz adds brightness and intelligibility to the voice. The bass emphasis (proximity effect) when used close to the mouth—see the dotted lines in the graph—adds warmth and fullness to the voice.


Pairing the Mic with the Sound Source

Next, let's look at what you're planning to mic. Musical instruments and voices have frequency ranges as indicated on the chart below. The darker orange indicates the range of fundamental frequencies, and the lighter shade represents the range of the highest harmonics or overtones of the sound source.

A mic that responds evenly to the full range of an instrument will reproduce the most natural sound.

Vocal and Instrument Frequency Response Chart
Vocal and Instrument Frequency Response Chart

When you compare the frequency range of the SM57 to this chart, it's easy to understand why it's a staple in most mic lockers. Often called "the industry workhorse," it does a very good job of capturing the natural sound of most instruments across their frequencies.

Need practice? There are hundreds of specification sheets for microphones on the Shure site. Using the instrument chart above, look at the frequency ranges on the spec sheets for a few different mics: maybe the PGA56, BETA®181, or the "Thriller" SM7B for starters. We bet you'll be able to match them to their most popular applications. Down the road, that may help you to choose the right mic for your particular application.

Davida Rochman
A Shure associate since 1979, Davida Rochman graduated with a degree in Speech Communications and never imagined that her first post-college job would result in a lifelong career that had her marketing microphones rather than speaking into them. Today, Davida is a Corporate Public Relations Manager, responsible for public relations activities, sponsorships, and donation programs that intersect with Shure at the corporate and industry level.